1
Our Solution
  • PRIME POWER SYSTEM
    PRIME POWER SYSTEM
    Manual and remote start for gen-sets with electronic engines. InteliNanoNT MRS starts, controls and monitors the gen-set and controls the circuit breaker to supply the load. The generator is protected by built in over/under voltage and frequency protection systems. The controller communicates with the engine management unit via a CAN J1939 bus and shows engine values and alarms on a graphical LCD screen. The controller enters sleep mode when the generator is not being used, allowing extended battery life for the unit. Current measurement is the key feature of the InteliNanoNT Plus, allowing the user to maximise engine power.

    2017-06-03

    read more
  • STANDBY SYSTEM
    STANDBY SYSTEM
    Stand-by gen-set with electronic engine. InteliLiteNT AMF 25 continuously monitors a mains supply and automatically starts an engine and switches load to a standby generator set in case of mains failure.   The service provider can monitor the gen-set operation remotely via GPRS modem.   The operator can use LiteEdit for a single gen-set view or WebSupervisor for total fleet management.   The generator is protected by a built in over/under voltage and frequency protections as well as IDMT overcurrent protection.   The controller communicates with engine management unit by a CAN J1939 bus. Engine values and alarms are visible on a graphical LCD screen in plain language – no need to learn cryptic flashing or numeric error codes.

    2017-06-03

    read more
  • STANDBY SYSTEM WITH SOFT RETURN
    STANDBY SYSTEM WITH SOFT RETURN
    Stand-by emergency gen-set accomplishes power supply to essential load during power drop.   The controller automatically starts the gen-set in case of mains failure and switches load to generator. When mains power returns, it synchronizes the generator back, softly unloads it and stops the engine.   Generator automatically synchronizes to mains in Test mode. Test mode can be used to check the gen-set condition and to provide uninterrupted power supply in case of expected mains failure.   Status of the gen-set is displayed in the distribution point.   InteliMonitor is used for remote monitoring and control; connected via IB-Lite.   History file with performance log stored in InteliCompactNT SPtM allows easy backtracking and problem solving.   Seamless communication with engine’s electronic injection control unit, all important values and alarms are visible on screen of InteliCompactNT and stored to the history file in plain language.

    2017-06-03

    read more
  • RENTAL SETS
    RENTAL SETS
    Containerized rental gen-sets are deployed as temporary and mobile power generation units providing essential energy for subsystems and construction machinery on building projects or civil engineering applications where mains power is not available or has been manually disconnected.   The application shows rental gen-sets fitted with the latest remote communication module InternetBridge-NT which enables the central control facility and mobile service engineers to efficiently monitor, control   and supervise equipment wherever it is located. By using the supportive cloud-based software applications such as WebSupervisor, rental operators can significantly improve operational control.   Each gen-set can be used in Stand-by, Single parallel to mains and Multiple parallel modes according to the position of Mode selector switch.

    2017-06-03

    read more
  • COMBINED HEAT AND POWER (CHP)
    COMBINED HEAT AND POWER (CHP)
    CHP (also known as cogeneration) is the most efficient way of using fossil or renewable fuel.   It provides output of power (3 phase electricity) and heat (hot water), which is recovered from the cooling system and flue gases.   The overall power and heat consumption of the application can be covered by the CHP system. Export of energy or heat is also possible.   All analog and binary signals both from the engine and from the auxiliary systems are measured by InteliSysNTC BaseBox and its accessory modules.   Complete control of auxiliary technologies is done by built-in PLC module.   All data measured from auxiliary equipment are stored in a history file.   Remote control and monitoring is available.   Only the most important analog inputs / outputs and binary inputs / outputs connections are drawn.

    2017-06-03

    read more
  • START-UP SYNCHRO GENSETS
    START-UP SYNCHRO GENSETS
    Application for faster start-up sequence of multiple generators.  No need to synchronize generators by standard way and wait until all of them are synchronized on the same bus. Suitable for standby applications. Eliminates possible blackout time. Ideal for systems running on UPS. System available at full capacity in 8-10 seconds from start command. Start-up time remains constant even if the number of generators is increased to 10, 20 or 31. To avoid delaying availability of the system due to slow-starting generators or other problems, any engines that fail to reach running speed within a specified time are “rejected” from the scheme and, if able, are left to perform traditional synchronizing after the majority of sets have become available. Traditional synchronizing is available to allow for slow-starting generators. Automatic switching to traditional synchronizing in case insufficient sets are available to meet load’s requirements. The soft magnetizing of feed transformers – solves the problem where grid supply is not capable of supplying the inrush and decreases the overall cost of the installation.

    2017-06-03

    read more
  • SHIP POWER MANAGEMENT SYSTEM
    SHIP POWER MANAGEMENT SYSTEM
    Two auxiliary generators and one shaft generator deliver electricity for the systems of the ship. Generators are controlled by GeCon software in MINT configuration. Power Management System (PMS) can work in three basic operational modes: • MANUAL – complete manual control • SEMI-AUTO – synchronizing and load-sharing is automatic; gen-set start/stop and load transfer between aux and shaft generators in manual • AUTO – complete automatic control PMS continuously evaluates load reserve on the bus and blocks start of the bow thruster if the load reserve is insufficient. PMS automatically trips the non-essential consumers, if the power system is overloaded. PMS can control up to 10 independent circuits of non-essential consumers. Freely programmable built-in PLC functions can be used to create specific settings of behaviour by customer.

    2017-06-03

    read more
  • MAINS PROTECTION FOR RENEWABLE RESOURCES
    MAINS PROTECTION FOR RENEWABLE RESOURCES
    Solar and wind are increasingly popular and cost-effective options for the generation and supply of power for both commercial and residential use. For operating the supply in parallel to the mains, protections are required, both for the network and equipment. It is important that these protections comply with the local utility’s standards. ComAp protection relays are the perfect solution providing advanced features, easy installation and intuitive operation.   In Solar/Wind applications on-site technical support (and ready access to a qualified technician) isn’t always an option: The MainsPro protection relay features automatic reset, remote communication and reliable monitoring of the system functions to provide   a reliable, cost-effective and trouble-free operation.   Advanced communication, remote monitoring and data/ event logging make InteliPro the ideal solution for your smart applications. This highly flexible protection relay combines powerful standard features with near endless optional features enabling you to build the ideal system for protecting your renewable energy investments.

    2017-06-03

    read more
  • PUMP SYSTEM
    PUMP SYSTEM
    InteliDrive Nano WP makes complete control, monitoring and protection of diesel engine.   The controller:   • continuously monitors the tank fluid level • automatically starts the engine in case of low level • ramps the engine speed up to full power • automatically ramps the engine speed down and stops the engine in case of high level   The J1939-CAN interface simplify wiring to the engine.

    2017-06-03

    read more
  • DC GENERATOR FOR OFF-GRID POWER SYSTEMS
    DC GENERATOR FOR OFF-GRID POWER SYSTEMS
    Batteries are in most cases the only one source of energy for Off-Grid telecom BTS (Base Transceiver Station) equipment. Batteries are charged by DC (Direct Current) generator – Hybrid solution.   InteliDrive DC controller makes complete monitoring, control and protection of the whole Hybrid system. Charging algorithm implemented in InteliDrive   Lite DC controller uses the DC generator output most effectively by variable engine speed control (less power requirement = lower RPM = lower consumption). Hybrid system can be extended with other especially renewable energy sources (Solar panel, Wind Turbine, Fuel Cells etc.). InteliDrive Lite DC ensures to be all energy sources utilized effectively with respect to reliability, battery life time, fuel consumption and floating load.   Remote monitoring of the whole system ensures minimization of operational costs (OPEX).   Automatic mode starts the generator once battery bank voltage drops under critical limit and charges the battery back to maximum possibly capacity.

    2017-06-03

    read more
  • GAS COMPRESSOR
    GAS COMPRESSOR
    Gas compressor is driven by a combustion engine.   InteliDrive DCU Industrial makes complete control, monitoring and protection of the engine and compressor.   Sophisticated control algorithm using build-in PLC modules accomplishes optimal running conditions for the compressor.   Speed of the engine is determined according to the suction and discharge pressures of the compressor.   Additional unload and by-pass valves are controlled by InteliDrive DCU Industrial in dependence on both suction and discharge pressures.

    2017-06-03

    read more
  • BI-FUEL/DUAL FUEL WITH PARALLELING GENSETS
    BI-FUEL/DUAL FUEL WITH PARALLELING GENSETS
    InteliBifuel does not interfere with the existing gen-set / engine controller therefore the functionality of the current application remains the same after Bi-fuel conversion.   The InteliBifuel conversion application is suitable for any type of gen-set/engine mode of operation (island, synchronization, paralleling). Financial savings are achieved via the substitution of up to 80% of the existing engines diesel consumption with gas (extended operating times without refuelling are also realized).   InteliBifuel controllers offer fuel flexibility and seamless transition between diesel and Bi-fuel operation modes as required (e.g. in case that gas is not available). Various types of gases can be used as the substitute fuel: natural gas, well gas, landfill gas, coal gas, propane gas, biogas etc.   Possible emission reductions of CO2, NOx, SOx and PM can be expected compared to original 100% diesel operation.   The InteliBifuel solution is a fully automatic solution which is mainly concerned with engine safety, gas is dynamically adjusted and optimised via a gas throttle valve.   All parts and parameters of the Bi-fuel solution are monitored and accessible from a single point.   Excellent remote monitoring features.

    2017-06-03

    read more

Copyright © 2015-2019 XIAMEN GTL POWER SYSTEM CO.,LTD.

#

top